|
|
SLG Series Options
|
Custom Engineered Solutions to Fit Your Requirements
- Custom Mountings.
- Exlar can provide a wide range of output options. The shaft may be a standard keyed shaft, a smooth splined shaft, or an ISO 9409 flange may also be supplied. To extend the radial load capacity special bearings can be utilized. The standard actuator is supplied with metric pilot diameters and mounting hole patterns. Other pilot diameters and hole patterns can be supplied. A side mount option is also available.
- Feedback options include encoder or resolver-based feedback configured for nearly any servo amplifier. Special feedback devices may also be incorporated.
- Special materials can be specified for the housing. Exlar can recommend various materials and coatings for demanding environments including salt water, chloride, food processing and more.
If your application requires special OEM options not listed above, please call us at 952-368-3434 to discuss the quotation and the longer lead time that applies to special options.
Motor Speed Designators
All Exlar T-LAM motors and gearmotors carry a standard motor speed designator as defined below. This is representative of the standard base speed of the motor, for the selected bus voltage.
|
| Designator |
Base Speed |
Motor Series |
| -50 |
5000 rpm |
SLG060 |
| -40 |
4000 rpm |
SLG090 |
| -30 |
3000 rpm |
SLG115 |
| 01-99 |
Special Order, Consult Exlar |
If the model number is created and the location for the motor speed designator is left blank, this is the base speed that each motor will be manufactured to. The model number can also be created including this standard speed designator.
Exlar also provides the flexibility to manufacture all of its T-LAM products with special base speeds to match the customer's exact application requirements. This may be a higher than standard speed motor, or lower base speed than standard, which will allow you to get the required torque, at a speed optimized to your application, and use the minimum amount of current from their amplifier.
The call-out for a special speed is configured in the model number by using a two-digit code from 01-99. These numbers represent the number, in hundreds, of RPM that will be the base speed for the particular motor.
For example, an SLG-090-010-KCGS-AB1-138-40 motor that normally has a 4000 rpm standard winding, can be changed to a 3300 rpm winding by changing the -40 to a -33. It can be changed to a 5000 RPM winding by changing the -40 to a -50.
Changing this speed designator will change the ratings of the motor, and these must be obtained from Exlar applications engineers. Also, it is not possible to produce every possible speed from 01-99 for each motor at each voltage so please contact Exlar applications engineers for confirmation of the speed that is desired for the application.
Housing Options
FG = Smooth White Epoxy
This option provides for a motor coated with FDA approved white epoxy.
SS = Stainless Steel Housing
This option provides a motor with all stainless steel construction. Housing dimensions for this option are not equal to the standard housing. Please inquire with Exlar for dimensions.
XH = Special Housing Option
Any housing option that is not designated by the above codes should be listed as XH and described at time of order. All special options must be discussed with Exlar engineering.
Motor Options
SLG motor options are described with a 3 digit code. The first digit calls out the stack length, the second the rated bus voltage, and the third the number of poles of the motor. Refer to the mechanical/electrical specifications for motor torque. All motors 8 pole. |
| 118 = 1 stack, 115 Vrms |
218 = 2 stack, 115 Vrms |
318 = 3 stack, 115 Vrms |
| 138 = 1 stack, 230 Vrms |
238 = 2 stack, 230 Vrms |
338 = 3 stack, 230 Vrms |
| 158 = 1 stack, 400 Vrms |
258 = 2 stack, 400 Vrms |
358 = 3 stack, 400 Vrms |
| 168 = 1 stack, 460 Vrms |
268 = 2 stack, 460 Vrms |
368 = 3 stack, 460 Vrms |
|
|
